Showing posts with label 1:72. Show all posts
Showing posts with label 1:72. Show all posts

Wednesday, September 30, 2026

Revell 1:72 Avro Lancaster Mk. I/III (Completed)






 





















Revell 1:72 Avro Lancaster Mk. I/III (Part 7)

 


Today I'll be finishing this Lancaster, and I'm quite excited to see it finally standing on it's own. But before I glue the wings onto the main spar, I want to add a panel wash to the model.

Usually, when I add on a panel wash, I'll add one color to the entire model. But in this case, with the black underside, I'm going to be starting by applying Tamiya Panel Line Accent Color (Gray) to all of the panel lines. 




I like to leave the wash alone to dry for around 24 hours. This gives the wash (which is a thinned down enamel paint) plenty of time to dry out and harden. This makes it easier for me to remove the wash and have the majority stay within the panel lines. 

Using a wide brush or some cotton buds, I dip them into Tamiya Enamel Thinner X-20. They just need to be dampened a bit, and you can easily begin removing the excess wash.

I also take care at this stage to pull the paint downwards in the direction of the wind flow along the wing.  I should also mention that I've applied the Panel Line Accent Color, over a gloss coat. The gloss is necessary at this stage as it allows you to remove the excess wash, whereas a flat coat will leave staining marks from the wash.




For the upper surfaces, as well as the yellow wing tips and tails, I've applied Tamyia Panel Line Accent Color (Dark Brown). I find that Dark Brown has a much nicer appeal than Black, as it's not quite as harsh and tends to blend in more with the model.

However, for natural metal subjects, I will apply a black wash as it stands out against the reflective nature of the silver paints.




Lancasters are quite well known for their large exhaust streaks that run along the wings, and I wanted to replicate this effect. 

Once again, I'm using the Tamiya Panel Line Accent Colors. These are easy to spray on, and if you don't like the effect, you can quickly wipe it away and try again. I like to layer several colors and this creates a unique effect that you can see on the real aircraft.

I started with a base layer of Dark Brown, and then I sprayed on top of that a few light coatings of Gray to replicate the lead effect from the gasoline.

This paint is very thin, and with the air from your airbrush, you can dry it out and spray on another layer. I will also mention that because this paint is so thin, it's incredibly delicate, and simply touching it can leave fingerprints. I would suggest that when you are done painting, add on a gloss or a flat coat to protect the streaks. 




Because of the black underside, I decided to only apply Gray as this color would stand out the most.  I sprayed the washes on with 25 PSI, and this was about 4-5 passes until I had built up the color and tone I desired.

I also like to keep these streaks random, maybe making a few a bit wider, or some that are more faded. This helps add a sense of reality to the subject.




The landing gear struts were added next, and this step is probably the most difficult stage of the model. The struts do fit together quite well, which was a relief; however, it is a bit of a fussy assembly, and I ended up super-gluing a lot of the parts to ensure they were properly secured to take the weight of the model.




You might recall from the first post that I showed the gun barrels, and that they were just long, rounded rods with no detail to them.

Well, thanks to my brother, he 3D printed me some 303. gun barrels that I could use. They are missing the cooling jacket holes, but you can see the flash hiders, and I think that they look really great. 




I decided to replace the antenna the sit on the nose. I cut off the thick plastic and replaced it with brass wire. 




Moving back to the fuselage, I've added on both of the tails. These don't really have a snug fit, so take care to properly align the tails.




I sprayed a flat coat on the entire model and the last of the smaller parts. Mr. Color 182 Flat Clear is my preferred paint, as it's very durable and restores the paint to its original tone.

With the flat coat applied, I removed the maskings from the turrets.  The new gun barrels do indeed look a lot nicer. To help them stand out more against a mostly black aircraft, I lightly drybrush a bit of Tamiya XF-56 Metallic Gray with my Vallejo Small Drybrush (B07001).




I removed and cleaned the canopy, and it's nice to see all of those details in the cockpit again.  The antennas were added to the nose, and like the gun barrels, they look much more to scale with the rest of the aircraft.




I applied a good amount of Mr. Cement along the top of the wing spar. And then I could carefully guide the wing into place.  It's a good and tight fit, so I feel that the wings are quite secured to the model. 





Lastly, I added the propellers and spinners.  The properller tips were painted with Tamiya LP-8 Yellow, and the rest of the blades were painted with XF-1 Flat Black, and a light coating of XF-50 Neutral Gray around the edges.

The spinners were painted in the same manner as the underside of the Lancaster.  Adding the propellers to the model was easy. Once the spinners are in place, it's easy to get glue around the mount, and this will prevent the propellers from turning. 




I've got a few things left to do on this model. The wing tip lights need to be added. I need to find my Micro Scale Kristal Klear glue so I can fill in and make those 2 small windows on the nose. And the pitot tube that sits on the fuselage has vanished, and I'm hoping it's not been swallowed up by the carpet monster.

Those things aside, this Lancaster is done!

This was a fun project to take on, and it was interesting to see how everything went together compared to the Airfix Lancaster. I built that one about 8 years ago, and it's fun to see how the 2 companies handled this subject. 

Revell went with an interesting choice; they wanted to keep things as thin and to scale as possible. And this certainly adds to the accuracy and finesse of the model, but it also makes things a bit on the fragile side.  It's actually very impressive to have a kit this big, only to pick it up and see just how lightweight it is. 

I think that some modelers might get frustrated with the landing gear assembly. They go together well, but you'll need a set of sturdy pointed tweezers.  And the rods for gun barrels is an interesting choice, especially when you consider how detailed the rest of the kit is.

I had a lot of fun with this project, especially with all of that painting. I'm eager to get those final details completed and take some final pictures of this kit.  I hope that you've enjoyed following along with this build, and that it might be helpful for you if you are building a Lancaster.



Revell 1:72 Avro Lancaster Mk. I/III (Part 6)

 


One of my favorite stages in modeling is adding the decals. I know that I'm in a minority with this opinion, but I find placing the decals onto the model to be a very relaxing and satisfying process. And it's where the model really comes together. 

I want to go through some of the issues I had while decaling this Lancaster, as well as show you how I fixed them.  I started by grabbing my decal solvents, some cotton swabs, and my pointed tweezers.  I also grabbed my Tamiya Decal Scissors (74031). These scissors make cutting around and trimming close to the decals a lot easier than using my hobby knife.

Lastly, I grabbed my dedicated decal brush. It's just the brush that came with an Airfix Zero starter set from a few years ago. But I only use it for decal solvents and clean water.



I first sprayed the entire Lancaster with a good, clear coat.  I used Mr. Color 46 Clear as this gloss is lacquer and will dry fast and very smooth.

The gloss coat will help with the decals' adhesion to the surface, and it should help prevent any silvering that might occur.



I'm going to be placing the large roundels on the top of the wings. I've soaked the decals in water for about 10 seconds, and then I placed them onto a tissue to rest until the decal has separated from the paper backing.

I brushed a generous amount of Micro Set (MI-1) onto the model where I wanted the decal to be placed.  The Micro set will help the decal adhere much better to the model's surface. It will also soften the decal slightly, allowing it to conform more to the surface details. This is especially helpful with the raised panel sections that run along the fuselage.



I slid the decal from the backing onto the wing. The Micro Set acts like glue, so it can immediately limit the decal's movement and placement. If this happens, just dip your brush in some water and spread it around the edges, and if you can, underneath the decal.  This will help loosen the Micro Set, allowing you to move the decal in the correct position. 

Once the decal is in place, you can add some more Micro Set, especially around the edges of the decal.

In this picture, I've left the decal to react to the Micro Set for about 5-10 minutes.  I've taken its companion product, Micro Sol (MI-2), the red bottle and applied a very generous coating around the decal.

Micro Sol is an aggressive product that will soften and melt the decal. As it dries, it will conform to the surface, giving the decal a more painted-on effect. It's very important at this stage to be careful not to touch the decal, as in its softened state it will be delicate and easily ruined. 




Here on the side of the fuselage, you can see a decal that has silvered.  Silvering is when air gets trapped inside the decal film and becomes visible.   This is a very frustrating thing to have happen, as it will become more obvious when a final flat coat is sprayed over the model.

But doesn't the gloss coat prevent silvering?

Yes, it can help prevent a lot of silvering, but silvering can also happen simply because of the brand of decals. Decals can be very inconsistent; one day they work perfectly, and other times you'll have a hard time getting the solvents to do anything at all. A lot of it comes down to the manufacturer, but it never hurts to do all you can to make the process easier on yourself.




The silvering along the fuselage is a bit more obvious against the black sections. To solve this issue, I'm going to add another generous coating of Micro Sol. But first, I'm taking a shape sewing needle, and I'm carefully stabbing the clear sections of the decal.

You don't need to press hard, as the decal film isn't that thick. But these holes will allow the trapped air to escape, and the Micro Sol to fill underneath the decal. 



I've added a second coating of the Micro Sol, and you can see how quickly the solution is getting into the decal.  You can also see how the decal has become wrinkled, and believe it or not, this is a normal part of the process.

Micro Sol can usually cause decals to wrinkle as it melts the decal. Don't panic, and DON'T add on more Micro Sol.  As the solvent dries, it will gently level out the decal and return it to its former glory.



As the decals are drying, you can see how well they are conforming to the surface and the recessed panel lines.  However, on the H and W, there is some trapped air that has caused bubbles to form.

Just as before with the silvering, I'm going to use my sewing needle and poke holes into these bubbles. Then I'll add on a bit more of the Micro Set, but only on the bubbles, as the rest of the decal doesn't need to be recoated.




If you are feeling ambitious and want to add to the effect of the decals, you can take a new and very sharp hobby knife. In this case, I'm using an Excel #11 Blade. And following along the panel line, I gently score into the decal while they are softened and drying.

Because the blade is very sharp not much pressure, or any, needs to be applied. I just kept a steady hand along the panel line.  This will help out later on when a panel wash is added to the model. Once I have all the panel lines cut out, I'll add on another coat of Micro Sol, which will help the decal edges conform around the panel lines.




When the Micro Set has dried completely, I'll seal in the decals with an acrylic gloss coat like Tamiya X-22.  I prefer to use Acrylic glosses over decals, as some Lacquers can be too aggressive and melt the decals, and ruin them.

One issue I ran into was on the wings. The black walkway lines that run down the wings aren't long enough to reach the roundels. And the roundels are too big; they barely fit into place and should be quite a bit smaller.  But I was very impressed with how well they reacted to the Micro Set and Micro Sol.

There are many other solvents on the market, like Mr. Mark Setter & Mr. Mark Softer. Or my favourite Tamiya Mark Fit Super Strong, which is very good for thicker and stubborn decals.  But many modelers swear by Micro Set & Sol, so if you see it in stock, it's a good idea to grab it quickly before someone else does.

I've got a few smaller parts remaining that need to be painted, but I'm getting pretty close to finishing this project.  I really love how these decals have turned out, and it's going to be great to see this bomber finally standing on its own.

To be continued...










Revell 1:72 Avro Lancaster Mk. I/III (Part 5)

 


Well, the Eduard masks I've been waiting for have arrived (as well as a lovely Eduard 1:48 A6M Zero). And I immediately added these to the clear parts. The window frames Revell produced are very thin, and it was going to be difficult to mask these myself. 

For the most part, the maskings fit quite well, and a few places would be covered further with some Mr. Masking Sol Neo. 




I added on several of the clear parts to the model, and I sprayed the window frames with a thin coating of Tamiya XF-1 Flat Black.  This was sprayed in 3 light layers to avoid paint build up, and any thin paint running under the maskings. 

Now that the clear parts have been painted, I can properly see just how thin those window frames are.




For this Lancaster, I wanted to layer on colors and create faded tones in the paint. To start off the Dark Earth, I first sprayed on a coating of Tamiya XF-52 Flat Earth.




Next, I sprayed random splotches of Tamiya XF-59 Desert Yellow, and XF-88 Dark Yellow 2. I chose colors that were lighter than the Flat Earth, as this would help create the faded effect.




The Dark Earth I'm using is a custom paint that I made a few years ago, coincidentally it was for the last Lancaster that I built. 

The paint is a combination of XF-49 Khaki and XF-72 Brown (JGSDF) at a ratio of 4-1.  This Dark Earth was thinned quite a bit, and it was lightly layered onto the previous paints.

At this stage, it's really easy to overdo it and paint on too thick a layer. It's important to remember that the paint will go on thin, but as it dries, it will darken and provide the desired effect.




I'm going to be freehanding the green, but this can be tricky. One method I've used is to use Silly Putty.  This will create a nice barrier around the paint and help prevent overspray.  Another nice thing about the Silly Putty is that it sticks well to the model and won't lift up the paint or leave behind any oils. And you can reuse it many times. 




Just as before, I'm starting with a dark base layer; this time, I'm using XF-13 J.A. Green.  The paint was thinned about 60-70% and sprayed at about 20 PSI. It took a bit of time to get everything covered, but I did find everything to be quite relaxing. 




For the splotches, I decided to use XF-5 Flat Green and XF-4 Yellow Green for the faded sections. Unfortunately, this picture washes out the effect of the Flat Green, but it did help in creating the desired effect.




My RAF Dark Green is a mixture of XF-27 Black Green and XF- 26 Deep Green, at a ratio of 4-1. However, you could try a 50-50 mixture of these paints if you find my mixture to be too dark.

Just as before with the Dark Earth, I've thinned the paint quite a bit and slowly layered it onto the green surfaces. Taking extra care now to get any onto the Dark Earth. And you can see how nice the marbled tones are with all of these colors.

"But wait, Tamiya already makes a Dark Green XF-81, why didn't you just use that paint?"

And you are absolutely correct, but I personally find that color to be a bit too dark and olive when painted next to the Dark Earth. Tamiya designed that paint with the release of their 1:32 Spitfire MK IXc, and I think it complements the XF-82 wonderfully.  It's just a matter of personal preference, and in this case, I wanted a brighter green for this Lancaster.




Fading the black was going to be a unique challenge. I started off by masking the brown and green, and then spraying a base coating of XF-1 Flat Black. 




I used XF-53 Neutral Gray for the larger faded patches. And for the smaller sections, I sprayed small dots of XF-19 Sky Grey. 




To create a faded black, I tested out a few paint mixtures, and I decided to mix XF-1 Flat Black with XF-63 German Gray at a 2-1 ratio.

The paint was thinned heavily and again lightly painted on, and I'm very pleased with this effect as it has the faded tone I wanted, and it's not a stark and bold black. 

The fading here is minimal compared to the brown and green sections, and this is because the black will be weathered further after the decals have been added.




Painting on all of these colors was something I was really looking forward to.  When you get the paint thinned and the pressure just right, painting becomes a relaxing process.  

These Lancasters spent a lot of time in the sun waiting for their nighttime missions, so it's not uncommon to see faded aircraft. As a result, this can really distort the paint and how we perceive it. 

There was a time when I wanted my models to have the exact RAF color, or RLM. I wanted all of my subjects to be color correct. But over the years, I've learned and seen how paint can fade and become distorted over time, and so these days I try to find colors that are just close. If you need an example, just search for Olive Drab aircraft. Sometimes it's black, sometimes it's very green, and depending on the location, it can bleach to a very pale color. It's such an inconsistent colour that matching it can be incredibly frustrating.

I provided a list of the colors that I used, and if you'd like to try them out, that's great. Or if you have your own mixture or preferred colors that's great too. These days, I try not to stress myself out too much with colors, and just get something close that I really like.

To be continued...